Square Truck Bodies

EDGE_Square_Bodies2 by .

Elliptical Bodies     |     Square Bodies     |     Contractor Bodies

Square dump bodies offer some advantages over the Elliptical bodies depending on application. The wide flat box floor accommodates wider implements easier and makes it easy for loaders and backhoes to work within the box. The square body also covers the wheels so additional fenders are not required. A square body offs slightly more cubic yard capacity over the elliptical body as well.

• Can accommodate wide, slide-in (skid) type implements easier
• Allows for easier “dipping” into with loader/backhoe buckets
• No fenders over rear wheels required by law
• Slightly increased cubic yard capacity vs Elliptical

Brochure

Samples of Square Dump Bodies Towmaster Builds

Standard Specifications

 Carbon SteelStainless Steel
DIMENSIONS:• 9’6” thru 15’6” long x 96" wide O.D.• 9’6” thru 15’0” long x 96" wide O.D.
FRONT PANEL:• 46", 50”, or 56” high, 3/16" HARDOX 450TM steel const with a reinforced top rail.
• Optional: 13” x 15” vertical doghouse cavity & lift blocks
• Optional: Inclined mount & rubber flap seal
• Optional: Removable tarp mtg brackets
• Optional: Vertical shovel holder(s)
• 46", 50”, or 56” high, 7ga Stainless Steel const with a reinforced top rail.
• Optional: 13” x 15” vertical doghouse cavity & Carbon Steel lift blocks
• Optional: Inclined mount & rubber flap seal
• Optional: Removable tarp mtg brackets
• Optional: Vertical shovel holder(s)
SIDES:• 30", 36”, or 46” high, 3/16" HARDOX-450TM interior panels
• 10ga GR50 outer panels with sloped center horizontal brace, & sloped rubrails
• Fully boxed top rails
• Full depth 7ga Stainless Steel rear corner posts
• Optional: Board pockets front and rear
• Optional: Inverted Angles on Top Rails for self-cleaning
• Optional: 3-line/4-line/dual 2-line sander manifold(s) @ rear corner posts
• Optional: Fixed or Removable 3-1/2” Bustin walk rail full length both sides
• Optional: "Tuck-A-Way" or “Fold-A-Way” access ladder - LH front, with interior step
• 30", 36”, or 46” high, 7ga Stainless Steel panels
• 18" radius corners
• Fully boxed top rails
• Full depth 7ga Stainless Steel rear corner posts
• Optional: Board pockets front and rear
• Optional: Inverted Angles on Top Rails for self-cleaning
• Optional: 3-line/4-line/dual 2-line sander manifold(s) @ rear corner posts
• Optional: Fixed Stainless Steel flat-bar tie rail full length both sides
• Optional: Removable 3-1/2” Bustin (Carbon Steel) walk rail full length both sides
• Optional: Carbon Steel "Tuck-A-Way" or Stainless Steel “Fold-A-Way” access ladder - LH front, with interior step
TAILGATE:• 30”, 36" or 46” high, 3/16" HARDOX-450TM main panel
• 10 ga GR50 outer panel & reinforcings
• 3 panel design
• 1-1/4" dia bottom pins
• 1" thick upper hinges w/bushings
• 1-3/4” dia top pins
• 3/8" alloy spreader chains (replaceable)
• 1” Steel Latches with dual over-center locks
• Airtrip ready linkage
• Optional: Lever top-pin release system (36” gate only)
• 30”, 36" or 46” high, 3/16" HARDOX-450TM main panel
• 10ga Stainless Steel outer panel & reinforcings
• 3 panel design
• 1-1/4" dia bottom pins
• 1" thick upper hinges w/bushings
• 1-3/4” dia top pins
• 3/8" alloy spreader chains (replaceable)
• 1” Latches with dual over-center locks
• Airtrip ready linkage
• Optional: Lever top-pin release system (36” gate only)
FLOOR:• 1/4" HARDOX 450TM steel
• Full width, one-piece construction
• 1/4" HARDOX 450TM steel
• 48” wide, one-piece construction
UNDERSTRUCTURE:• W8" x 13.0#/ft structural (I BEAM) longsills
• 8" structural channel rear bolster
• Optional: S10" x 25.0#/ft structural (I-BEAM) longsills
• Optional: TMTE-1820 hoist lift bracket incorporated
• Optional: 10" structural channel rear bolster
• W8" x 13.0#/ft structural (I BEAM) longsills
• 8" structural channel rear bolster
• Optional: S10" x 25.0#/ft structural (I-BEAM) longsills
• Optional: TMTE-1820 hoist lift bracket incorporated
• Optional: 10" structural channel rear bolster
PREP/PAINT:• Exterior & Underside industrially steel shot-blasted
• Urethane primed
• Exterior finish coated with Color Choice Polyurethane Enamel
• Underside finish coated with Gloss black Polyurethane
• Stainless Steel Exterior Acid Washed, left in Mill Finish
• Underside industrially steel shot-blasted
• Underside & Carbon Steel Parts Urethane primed
• Underside & Carbon Steel Parts finish coated with Gloss black Polyurethane
CABSHIELD:• 1/2 type, 24"
• Optional: Fixed “Weld-On” style
• Optional: Stationary “Free-Standing” style
• Optional: 2vert shovel holders style (Stationary only)
• Optional: Adjustable tubing strobe brackets
• Optional: Cabshield mounted reservoir brackets(Stationary only)
• Optional: Full Center window (Stationary only)
• 1/2 type, 24" Stainless Steel Construction
• Optional: Fixed “Weld-On” style
• Optional: Stationary “Free-Standing” style (Vertical Stand Carbon Steel Painted)
• Optional: 2 vertical shovel holders style (Stationary only)
• Optional: Adjustable tubing strobe brackets (Carbon Steel Painted)
• Optional: Cabshield mounted reservoir brackets(Stationary only)
• Optional: Full Center window (Stationary only)
SPILL SHIELD:• 1/4" Gr 50 steel construction
• 4”, 6”, or 12" extension
• Bolt together construction
• Body/sander bracket mounts
• Painted
• 1/4" Gr 50 steel construction
• 4”, 6”, or 12" extension
• Bolt together construction
• Body/sander bracket mounts
• Painted

Features and Options