Close

EDGE_Elliptical_Bodies by .

Elliptical bodies offer some unique advantages over the traditional square dump bodies, depending on your application. Elliptical bodies offer radius sides so material or odd-shaped items “self-center” in the box. This allows the material to flow out easier. The body design incorporates strength without the need for additional supports and provides an open area for side pre-wet kits. It also weighs less than a traditional square body.

• Materials flow out easier, no square corners to stick into
• Odd shaped or Large materials self center – tumble to the middle of the body
• Large radius is strong with corrugations every 2”
• Exterior is easier to wash and keep clean – no additional supports
• Body weighs less than comparable Traditional Square body
• Side Pre-Wet tanks can be utilized for balanced application

Samples of Elliptical Dump Bodies Towmaster Builds

Specifications

 Carbon SteelStainless Steel
DIMENSIONS• 9’6” thru 15’0” long x 96" wide O.D.• 9’6” thru 15’0” long x 96" wide O.D.
FRONT PANEL:• 46", 50”, or 56” high, 3/16" HARDOX 450TM steel const with a reinforced top rail.
• Optional: 13” x 15” vertical doghouse cavity & lift blocks
• Optional: Inclined mount & rubber flap seal
• Optional: Removable tarp mtg brackets
• Optional: Vertical shovel holder(s)
• 46", 50”, or 56” high, 7ga Stainless Steel const with a reinforced top rail.
• Optional: 13” x 15” vertical doghouse cavity & Carbon Steel lift blocks
• Optional: Inclined mount & rubber flap seal
• Optional: Removable tarp mtg brackets
• Optional: Vertical shovel holder(s)
SIDES:• 30", 36”, or 46” high, 3/16" HARDOX-450TM panels
• 18" radius corners
• Fully boxed top rails
• Full depth 7ga Stainless Steel rear corner posts
• Optional: Board pockets front and rear
• Optional: Inverted Angles on Top Rails for self-cleaning
• Optional: 3-line/4-line/dual 2-line sander manifold(s) @ rear corner posts
• Optional: Fixed or Removable 3-1/2” Bustin walk rail full length both sides
• Optional: "Tuck-A-Way" or “Fold-A-Way” access ladder - LH front, with interior step
• 30", 36”, or 46” high, 7ga Stainless Steel panels
• 18" radius corners
• Fully boxed top rails
• Full depth 7ga Stainless Steel rear corner posts
• Optional: Board pockets front and rear
• Optional: Inverted Angles on Top Rails for self-cleaning
• Optional: 3-line/4-line/dual 2-line sander manifold(s) @ rear corner posts
• Optional: Fixed Stainless Steel flat-bar tie rail full length both sides
• Optional: Removable 3-1/2” Bustin (Carbon Steel) walk rail full length both sides
• Optional: Carbon Steel "Tuck-A-Way" or Stainless Steel “Fold-A-Way” access ladder - LH front, with interior step
TAILGATE:• 30”, 36" or 46” high, 3/16" HARDOX-450TM main panel
• 10 ga GR50 outer panel & reinforcings
• 3 panel design
• 1-1/4" dia bottom pins
• 1" thick upper hinges w/bushings
• 1-3/4” dia top pins
• 3/8" alloy spreader chains (replaceable)
• 1” Steel Latches with dual over-center locks
• Airtrip ready linkage
• Optional: Lever top-pin release system (36” gate only)
• 30”, 36" or 46” high, 3/16" HARDOX-450TM main panel
• 10ga Stainless Steel outer panel & reinforcings
• 3 panel design
• 1-1/4" dia bottom pins
• 1" thick upper hinges w/bushings
• 1-3/4” dia top pins
• 3/8" alloy spreader chains (replaceable)
• 1” Latches with dual over-center locks
• Airtrip ready linkage
• Optional: Lever top-pin release system (36” gate only)
FLOOR:• 1/4" HARDOX 450TM steel
• 48” wide, one-piece construction
• 1/4" HARDOX 450TM steel
• 48” wide, one-piece construction
UNDERSTRUCTURE:• W8" x 13.0#/ft structural (I BEAM) longsills
• 8" structural channel rear bolster
• Optional: S10" x 25.0#/ft structural (I-BEAM) longsills
• Optional: TMTE-1820 hoist lift bracket incorporated
• Optional: 10" structural channel rear bolster
• W8" x 13.0#/ft structural (I BEAM) longsills
• 8" structural channel rear bolster
• Optional: S10" x 25.0#/ft structural (I-BEAM) longsills
• Optional: TMTE-1820 hoist lift bracket incorporated
• Optional: 10" structural channel rear bolster
PREP/PAINT:• Exterior & Underside industrially steel shot-blasted
• Urethane primed
• Exterior finish coated with Color Choice Polyurethane Enamel
• Underside finish coated with Gloss black Polyurethane
• Stainless Steel Exterior Acid Washed, left in Mill Finish
• Underside industrially steel shot-blasted
• Underside & Carbon Steel Parts Urethane primed
• Underside & Carbon Steel Parts finish coated with Gloss black Polyurethane
CABSHIELD: • 1/2 type, 24"
• Optional: Fixed “Weld-On” style
• Optional: Stationary “Free-Standing” style
• Optional: 2vert shovel holders style (Stationary only)
• Optional: Adjustable tubing strobe brackets
• Optional: Cabshield mounted reservoir brackets(Stationary only)
• Optional: Full Center window (Stationary only)
• 1/2 type, 24" Stainless Steel Construction
• Optional: Fixed “Weld-On” style
• Optional: Stationary “Free-Standing” style (Vertical Stand Carbon Steel Painted)
• Optional: 2 vertical shovel holders style (Stationary only)
• Optional: Adjustable tubing strobe brackets (Carbon Steel Painted)
• Optional: Cabshield mounted reservoir brackets(Stationary only)
• Optional: Full Center window (Stationary only)
SPILL SHIELD:• 1/4" Gr 50 steel construction
• 4”, 6”, or 12" extension
• Bolt together construction
• Body/sander bracket mounts
• Painted
• 1/4" Gr 50 steel construction
• 4”, 6”, or 12" extension
• Bolt together construction
• Body/sander bracket mounts
• Painted

Features and Options