Falls Plows

Falls by .

Towmaster is an authorized distributor for Falls Plows. Falls Plows manufactures tough, top-quality, industrial-grade snow handling equipment including Snow Plows, Snow Wings, Scrapers, Spreaders and Scarifiers. Reliability and innovation keep them the Midwest’s largest supplier of advanced design, high-quality truck, wheel loader and motor grader-mounted snow handling equipment.

Side Wings

FALLS SDL DIRECT HYDRAULIC SNOW WING – Truck Rear Mount

  • 8, 9, 10, 11, and 12-foot cutting edge lengths.
  • 3.5″ diameter double-acting hydraulic cylinders.
  • Nitrided cylinders for increased corrosion resistance.
  • 1-3/4″ wing hinge bolt.
  • Trip edge or trip moldboard available.
  • Equipped with Falls’ exclusive Wing Lock Valve with built-in relief.
  • Double-boxed wing construction eliminates twisting.
  • Two (2) cylinder control for precise positioning.
  • Heavy-duty construction throughout.
  • Works in conjunction with Underchassis Scraper to eliminate windrows.
  • Shown with optional nitrogen-accumulated hydraulic push bar extension.
RearWingTrk copy by . SDL Hyd Wing_Page_1 by .
FALLS TDL DIRECT HYDRAULIC SNOW WING – Truck Front Mount

  • 8, 9, 10, 11, and 12-foot cutting edge lengths.
  • 3.5″ diameter double-acting hydraulic cylinders.
  • Nitrided cylinders for increased corrosion resistance
  • 1-3/4″ wing hinge bolt.
  • Trip edge or trip moldboard available.
  • Equipped with Falls’ exclusive Wing Lock Valve with built-in relief
  • Hydraulic power front sideshift available.
  • Double-boxed wing construction eliminates twisting.
  • Two (2) cylinder control for precise positioning.
  • Heavy-duty construction throughout.
  • Shown with optional nitrgen-accumulated hydraulic push bar extension.
1ASD9SS Sander_Page_1 by . TDL Hyd Wing_Page_1 by .
FALLS HEAVY-DUTY CABLE SNOW WING for Trucks – front mount or rear mount

  • Convert any truck (3-ton and up) into an efficient snow fighter.
  • Clear up to 20 feet in one pass.
  • Widening operations.
  • Benching or shelving operations.
  • Works in combination with one-way plows, reversible plows and v-plows.
  • Maximize your machine and manpower.
  • Rear-mounted configuration available.
HDSnowWingTrk by . W Snow Wing_Page_1 by .

Plows

 FALLS POWER REVERSIBLE E-1 SERIES PLOWS

  • Heavy-duty double A-frame.
  • Quick coupler plow units attach to push plate with 2″ diameter pivot bolt allowing desired snow plow oscillation for cleaner plowing.
  • Five rolled, heavy channel iron ribs provide maximum rollboard rigidity. Horizontal channel braces reinforce transverse stability.
  • Moldboard may be tilted forward or back depending on snow and road conditions.
  • Nitrided cylinders for increased corrosion resistance.
  • Bottom support structure is constructed of 4″ x 4″ x 3/4″ A-36MOD angle iron reinforced between bolt holes.
  • Heavy-duty tubular push frame distributes plowing stresses across full length of moldboard.
  • Two heavy-duty single-acting reversing cylinders for quick control with hydraulic cushion valve for circuit protection.
  • Standard screw-adjustable mushroom shoes.
Reversible E-1 by . Reversible E-1 Slotted Trip by . Reversible E-1 Trip Edge by . PR Series Plows Lit_Page_1 by .
FALLS POWER REVERSIBLE E-1 SERIES ONE WAY PLOWS

  • Heavy-duty double A-frame.
  • Quick coupler plow units attach to push plate with 2″ diameter pivot bolt allowing desired snow plow oscillation for cleaner plowing.
  • Four rolled, heavy channel iron ribs provide maximum rollboard rigidity. Horizontal channel braces reinforce transverse stability.
  • Moldboard may be tilted forward or back depending on snow and road conditions.
  • Nitrided cylinders for increased corrosion resistance.
  • Bottom support structure is constructed of 4″ x 4″ x 3/4″ A-36MOD angle iron reinforced between bolt holes. Discharge end is reinforced with an additional 1/2″ x 7″ 1045 steel plate.
  • Heavy-duty tubular push frame distributes plowing stresses across full length of moldboard.
  • Two heavy-duty single-acting reversing cylinders for quick control with hydraulic cushion valve for circuit protection.
  • Nitrided cylinders for increased corrosion resistance.
  • 3/8″ landslide plate has renewable nose.
  • Standard screw-adjustable mushroom shoes.

 

PwrRev_E_oneway_ref by . PR Series Plows Lit_Page_1 by .
FALLS TER-SERIES TRIP EDGE HEAVY-DUTY REVERSIBLE PLOW

  • Three (3) torsion spring trip sections.
  • Standard cushion valve.
  • Heavy-duty, simplified oscillating A-frame, 4″ x 4″ x 1/4″ (101.6mm x 101.6mm x 6.35mm) square tubing.
  • 1-1/2″ (38mm) center pivot rod.
  • 1/2″ (12.7mm) thick end ribs.
  • 2″ (51mm) swivel bolt.
  • 3/4″ (19mm) chrome-vanadium torsion springs, two (2) per section.
  • Optional coatings available for moldboard face.
  • Standard screw adjustable mushroom shoe assemblies.
  • Double, overlapping, 7 gauge (5mm) and 10 gauge (3mm), formed box sections provide full length reinforcement.
TER_comp by . TER Trip Edge 2011_Page_1 by .
FALLS SNOW EXPRESS PLOW

  • 5 rolled, heavy channel iron ribs deliver maximum moldboard rigidity. Horizontal braces provide reinforcement and stability.
  • Moldboard tilt feature provides the flexibility to tilt the moldboard forward or back depending on snow and road conditions.
  • Precise moldboard curvature provides proper lift, roll and throw of snow for maximum efficiency and easier plowing.
  • Discharge end is flanged and additionally reinforced with 1/2-inch roundbar.
  • Bottom support structure is 4″ x 4″ x 1/2″ A-36 MOD angle iron reinforced between the bolt holes.
  • Push frame attaches at 4 pins – 1-1/4″.
  • A-frame push plate is double tubular construction. hitch unit will attach through large diameter hinge bolt (2″) to allow the plow to oscillate to follow changing road contour.
  • Standard screw-adjustable mushroom shoes.
  • Heavy-duty reversing push frame distributes plowing stress across the entire length o fthe moldboard.
  • Optional slotted trip or compression spring trip tilting bars.

 

SnowExpress_ref by . XPR 2011_Page_1 by .
FALLS V-PLOW

  • 90 degree included blade angle provides the easiest pushing V-Plow in the industry.
  • Shoe adjustment, including nose shoe, is made easily without the use of tools.
  • Easily adaptable to major quick hitches and conventional hitches.
  • Lift and roll of the moldboard discharges snow with ease and in one fluid motion.

 

Vplow_truck by . V-Plow Literature_Page_1 by .
FALLS ONE WAY PLOW

  • Smooth rolled moldboard for a clean lift, roll and throw of snow.
  • Discharge end is rolled and formed for additional strength. In addition, a 1/2″ round bar is formed and welded to the rib for greater stiffness.
  • The 4″ channel iron ribs extend from the top moldboard angle to the bottom support angle.
  • Top moldboard angle is 2″ x 2″ x 3/16″ angle.
  • Bottom support angle is 4″ x 4″ x 3/4″ A-36 MOD angle boxed between the bolt holes. Discharge end is reinforced with an additional 1/2″ x 7″ 1045 steel plate.
  • Screw-adjustable oscillating shoes are standard.
  • Landslide plate has renewable nose.
  • Fixed-angle push frame is heavily reinforced and attaches to the moldboard at 5 points with 1-1/4″ pins.
  • Hitch adapter and swivel plate allow plow to follow the changing road contours.
  • Rigid tilting bars are standard.
  • Standard built-in snow deflector.
OneWay_lo_2011 by . One Way Plow Lit_Page_1 by .

FALLS ONE WAY SLOTTED TRIP-EDGE PLOW

  • Smooth rolled moldboard for a clean lift, roll and throw of snow.
  • Discharge end is rolled and formed for additional strength. In addition, a 1/2″ round bar is formed and welded to the rib for greater stiffness.
  • The 4″ channel iron ribs extend from the top moldboard angle to the bottom support angle.
  • Top moldboard angle is 2″ x 2″ x 3/16″ angle.
  • Bottom support angle is 4″ x 4″ x 3/4″ A-36 MOD angle boxed between the bolt holes. Discharge end is reinforced with an additional 1/2″ x 7″ 1045 steel plate.
  • Screw-adjustable oscillating shoes are standard.
  • Landslide plate has renewable nose.
  • Fixed-angle push frame is heavily reinforced and attaches to the moldboard at 5 points with 1-1/4″ pins.
  • Hitch adapter and swivel plate allow plow to follow the changing road contours.
  • Rigid tilting bars are standard.
  • Standard built-in snow deflector.
SlottedTripOneWay by . OneWayPlow_2011_Page_1 by .
FALLS POLY TRIP EDGE PLOW

  • Standard Cushion Valve
  • 1/2″ x 5″ (12.7mm x 127mm) deep vertical ribs
  • Heavy-duty single section trip with 6 trip springs
  • Optional screw adjustable mushroom shoe assemblies
  • Heavy-duty, simplified oscillating A-frame. 4″ x 4″ x 1/4″ (101.6mm x 101.6mm x 6.35mm) square tubing
  • 3/4″ (19mm) center pivot rod
  • 2″ (51mm) swivel bolt
  • 3/8″ (9.5mm) VHMW Moldboard
PolyPlow_main by . PTE Literature_Page_1 by .
FALLS ROX SNOW PLOW

  • Lower left side for improved driver visibility and safety
  • Five heavy rolled channel ribs, horizontal braces for enhanced moldboard reinforcement
  • Precise moldboard curvature provides lift, roll, and throw of snow for maximum efficiency
  • 12-foot moldboard option

Scrapers

FALLS REVERSIBLE UNDERBODY SCRAPER – Model IBR-10A

  • AASHO and carbide punch.
  • 500 psi pressure reducing valve included.
  • Two double-acting 3-1/2″ diameter revesible cylinders.
  • Optional power lock pins available with monoblock sequence valve.
  • Compact design for easier installation and better blade contact angle.
  • Two 1/2″ x 6″ DBC cutting edges.
  • Hydraulic Accumulator System for consistent pressure.
  • 1″ thick one-piece circle plate.
  • 1-3/4″ cold-rolled steel hinge shaft.
  • Moldboard is 1″ x 20″ with a 17″ radius.
  • Patent #5,921,010.
RevScrap_ref by . IBR Literature_Page_1 by .
FALLS UNDERBODY SCRAPER – Model IB-10A

  • AASHO and carbide punch.
  • 500 psi pressure reducing valve included.
  • 3″ cushioned hydraulic cylinder cylinder.
  • May be installed in combination with plow and wing.
  • Compact design for easier installation and better blade contact angle.
  • Two 1/2″ x 6″ DBC cutting edges.
  • Hydraulic Accumulator System for consistent pressure.
  • 1-1/2″ cold-rolled steel hinge shaft.
  • Moldboard is 3/4″ x 20″ x 10′, 17″ radius.
  • High-visibility end markings.
  • Heavy-duty construction throughout.
  • Patent pending.

 

Scraper-A by . IB Literature_Page_1 by .

Spreaders

FALLS TAILGATE SPREADER – Model IASD9

  • Berm Chute
  • 3/8″ Thick Auger, 9″ Diameter
  • Self-Leveling Spinner with Six (6) Flights
  • Right or Left Hand Discharge
  • Direct Hydraulic Shaft and Spinner Drive
  • End Plates Constructed of 1/4″, A-36 Steel
  • Auger Shaft Tapped To Accept Speed Sensor
  • Oversized Hopper Opening To Reduce “Bridging”
  • Parker Torqlink TBO and Roller Stator Hyd. Motors
  • Hopper Constructed of 7 Gauge A607-50 Steel
  • Full Length Hinged Bottom Cover with Easy Latch System
  • Full Length Hinged Top Cover for Dumping Operations with Two (2) Position Gate Opening.
Spreader Spreader9_Page_1 by .
FALLS STAINLESS STEEL TAILGATE SPREADER – Model IASD9SS

  • 3/8″ thick auger.
  • Oversized hopper opening to reduce bridging.
  • Parker Torqlink TBO and Roller Stator hydraulic motors.
  • Self-leveling spinner with 6 flights.
  • Hopper constructed of 7 gauge stainless steel.
  • Berm chute delivers flow to road shoulder.
  • End plates constructed of 1/4″ stainless steel.
  • Right or left hand discharge.
  • Auger shaft tapped to accept speed sensor.
  • Direct hydraulic shaft and spinner drive.
  • Full-length hinged bottom cover with Easy Latch System for easy clean-out in any weather.
  • Full-length hinged top cover with 2 position flow-control gate opening for fast, one-person dumping operations.

 

9inchSpreader_SS_ref by . 1ASD9SS Sander_Page_1 by .

Hitches

FALLS X1 MODIFIED HUSTING HITCH QUICK COUPLER

  • This is a modified version of the 29″ Husting Hitch. It has been modified to fit Falls Standards so now it’s stronger, more flexible and reliable. A chain left has also been added to the truck-mounted portion. This delivers a smooth, “no pry” lifting action. The plow mount is made of rugged 8″ x 4″ x 1/2″ angle iron with the entire length of the sliding pin slot reinforced with 1″ square and 5″ x 3″ x 5/16″ angle iron. It also has a center pivot pin which allows oscillation for closer manufacturing tolerances between truck and plow portions.

 

HustingCustomHitch by . HitchSystems_Page_1 by .
FALLS X4 PIN AND LOOP QUICK COUPLER

  • The Falls X4 Pin and Loop Quick Coupler features a plow-mounted loop and truck hitch-mounted coupler that delivers coupling that’s fast and reliable. The truck hitch coupler is a positive drop-in, lever actuated pin. This hitch system is interchangeable with other similar loop couplers.

 

BonnellCustomB by . HitchSystems_Page_1 by .
FALLS #46B CUSTOM FRAME HITCH WITH RAPID PUSH BAR ATTACHMENT

  • The Falls #46B Hitch System is the very finest in plow and wing hitches. The Falls Custom Frame Hitch is ruggedly constructed and designed for very heavy snowplowing and snow-winging service in all truck classes. Constructed of 1/2″ thick steel plates and heavily reinforced throughout.

 

46BRapidPushHitch by . HitchSystems_Page_1 by .
FALLS X8 JAW QUICK COUPLER (JQC)

  • The Falls X8 Jaw Quick Coupler is a two pointed latch system which keeps the moveable components attached to the snow plow. The solid components are apart of the truck-mounted assembly. This hitch system is interchangeable with other similar jaw couplers.

 

48B_JawQuikCplrHitch by . HitchSystems_Page_1 by .

Skid-Loader Plow

FALLS SSTR REVERSIBLE SNOW PLOW for Skid Steer Loader Mount

  • Heavy-Duty Construction
    • 31″ moldboard height, 10 gauge Grade 50 steel
    • 7 gauge Grade 50 steel box-formed reinforcement
    • Superior push frame and reversing circle
    • 8 foot (750 lbs) and 9 foot (800 lbs.) models
  • Industrial-Style Single-Acting Reversing Cylinders
    • Full 30 degree angle left and right
    • 1.5″ rod, 2″ diameter, 11.75″ stroke.
    • Mechanical stops to prevent over-rotation
  • Adjustable Safety Trip Cutting Edge to minimize impact on plow and loader when encountering hidden obstacles.
    • Standard replaceable 5/8″ x 6″ cutting edge
    • Adjustable Safety Trip Cutting Edge
  • Universal Quick Coupler Mounting Plate mounted with precise forward pitch
  • Utilizes existing skid steer loader auxiliary hydraulic controls
  • Options include END GATES, wear shoes, high-visibility blade guide-ons, rubber snow deflector
  • Full 2-year warranty
SkidPlowCAT by . SSTR Skid Steer Snow Plow_Page_1 by .